HobbyFarms.com


Your E-mail:
Hobby Farms - Current Issue

Urban Farm Magazine

Printer Friendly

How Do I ... Build Raised Beds

Growing in raised beds has many advantages: It can be easier on aging backs and knees, and the soil conditions inside a raised bed can easily be kept optimal.


Text by Kelly Wood/Photos by Rhoda Peacher

Build Raised Beds Step 4
Step 4

Growing in raised beds has many advantages: It can be easier on aging backs and knees, and the soil conditions inside a raised bed can easily be kept optimal. By relegating external areas to the compaction of walking and wheelbarrows, the contained soil stays aerated, thus draining better. Raised beds can be maintained by simply topping with compost or mulch.

They extend a gardener's growing season because the walls collect early spring sun and warm up before native soil, giving plants and seeds a jump on the growing season. I also like that my raised beds look tidy, since I mow right up to the wooden edge of the bed itself.

 

Materials List

  • Saw (power or chop)
  • Power drill with screwdriver bit and small drill bit for pilot holes
  • Measuring tape
  • Pencil 
  • 4 12-foot, 2"x6" cedar boards 
  • 4 8-foot, 2"x6" cedar boards
  • 1 6-foot, 2"x6" cedar board, cut into 6 pieces (no more than 11 inches each)
  • 40 2¼-inch decking or exterior screws 
  • A helper! This project is tricky (but possible) to assemble with only one set of hands (and feet)
Instructions

Step One.
Determine where you want the beds to be and how large an area you want to grow in. While the sides can be as high as you'd like, raised beds should not be so wide that you can't reach the middle from either side for planting, harvesting and maintenance.

Step Two.
Obtain the lumber to build the beds. This is often a complicated decision because of the many choices. In our Oregon area, cedar, while expensive, is the most common choice. When we lived in California, redwood was by far the most prevalent. Both of these woods have a natural resistance to rot and decay, which is imperative since they will be filled with dirt and water for their entire useful lives.

Another option is newer, recycled "lumber," commonly known by the brand name Trex, which is a mix of sawdust and recycled plastic.

Pile It On
Whenever I read articles about starting a garden, they always advise paying close attention to site location.

Exposure to light, wind and elements is important, but soil is also an important consideration. While it's usually listed second to exposure, I personally feel it's No. 1 in importance. It's possible to change the exposure of your growing area, whether by selective tree trimming, shade cloth and screens, or planting hedges to reduce wind and increase warm microclimates. Soil, however, is a much more difficult thing to change. No one in their right mind wants to remove tons of native soil and replace it with imported, no matter how high quality. And even if this were possible, and not prohibitively expensive, some experts say that it's impossible to completely rectify soil problems, particularly overall pH levels. I believe that piling on top of existing conditions is the best way to improve your soil, building it up with compost and beneficial amendments, much as happens in a deciduous forest. The easiest way to achieve this is with a raised bed.

Raised beds can be placed almost anywhere, provided other garden conditions have been met—good exposure and convenience for the gardener. If your beds are out of the way or difficult to get to, their regular care will fall to the wayside and success will be elusive. There are a few caveats when placing raised beds—ideally, you want to avoid placing them over the root systems of large, thirsty trees whose roots will invade the improved soil area and steal water and nutrients from the intended bed residents. If you have pernicious rodents like gophers or field mice, you can lay hardware cloth at the base to impede invaders. Other than that, beds can even be placed over excessively weedy areas or on solid subsurfaces like pavement, as long as protective underlayment or gravel to aid drainage is provided before filling.

Although expensive, this will last indefinitely and often can be bent into interesting shapes to increase visual interest. Other alternatives are stone, cinder blocks, fieldstone, bricks and more; pretty much anything, except treated lumber that can leach hazardous chemicals, can be used as bed edges.

Step Three.
Cut the material to the desired sizes for your bed walls. Remember to account for overlap at the ends. For sides that are longer than 4 or 5 feet, plan to have upright supports in the middle to prevent the longer boards from bowing out.

Step Four.
Drill pilot holes in the wood to prevent splits during assembly. Screw the wall pieces onto the support braces. Use screws instead of nails since screws will hold better as the wood shrinks and swells over time and seasons. Nails have a tendency to loosen and pop out.

Step Five.
With a helper, screw the side walls to the end walls. When complete, the raised bed will be ready to place.

Step Six.
Again with a helper, carry the finished bed to its intended location.

Build Raised Beds Step 5
Step 5
By having a "free-floating" bed, you can move it around and adjust it until you're happy with the location. At this point, it can be left as is; the weight of the wood combined with filling will keep it in place. Otherwise, you can sink metal stakes inside the walls and secure them with pipe clamps prior to filling. This lends some additional support to the walls and prevents shifting of the finished bed. These pipes can also be used to support hoops or trellising. I salvage old metal pipe, but wooden stakes can also be used. Make certain they are a rot-resistant variety and screw them to the bed walls from the outside.

Build Raised Beds Step 7
Step 7
Step Seven.
Put underlayment in the bed. This can be as simple as newspaper to block grass and other tenacious weeds or as elaborate as landscape cloth and metal mesh. On top of this you can place either manure or unfinished compost, which will eventually rot, providing roots with a nutrition boost, or simply fill the raised bed with planting soil or finished compost. If you start with unfinished compost, be sure to top it off with a fine-textured planting mix or finished compost when doing final planting.

About the Author
Kelly Wood farms and heavily mulches her raised beds in Portland, Ore.

Step Eight.
Enjoy! With regular mulching, you can keep the beds filled and see a happy, thriving population of earthworms and other beneficial organisms that perform the tilling and incorporating work for you.

Top

Read More Livestock & Pets

This article first appeared in the May/June 2008 issue of Hobby Farms magazine. Pick up a copy at your local newsstand or tack and feed store. Click Here to subscribe to HF.

 Give us your opinion on
How Do I ... Build Raised Beds

Submit a Comment
Reader Comments
I see you're stacking two 6x12s...why wouldn't you just use a 2x12? I see you're using a cordless drill, instead of building the bed off-site why not just build it write there where it is intended to stay.
One can buy corners at the hardware store to screw into the corners to keep them from coming apart
Gomer, San Pablo, AL
Posted: 1/29/2013 5:10:36 PM
I wish I would have read this before trying on my own. Thank you!
Kimberly, Midlothian, TX
Posted: 9/7/2012 6:29:38 AM
A few more details would have been very helpful -- or a photo that showed the corners of the box more clearly. I'm confused by the 6-foot 2"x6" that is specified to be cut into 6 pieces "no longer than 11 inches." I figured out -- by looking at the pictures -- that the 11 inches specification means that these 6 pieces are intended to be used vertically and that two of them are used as supports midway along the longest sides of the box (to keep the boards from bowing out, I presume, or to keep them from separating at the weakest spot along the sides and allowing dirt to spill out). OK -- but where do the other four pieces go?? Are they to be used in the corners of the box as corner supports?? MORE DETAILS next time! You give a good general description but not enough information for a really helpful "how to."
Lynda, Seattle, WA
Posted: 3/1/2012 7:21:04 AM
Thanks for teaching me this.
Derek, CHICAGO, IL
Posted: 2/19/2012 5:56:38 PM
View Current Comments

Product Spotlight
Hobby Farm Rewards 
Member Login »

facebook


Information on over 200 horse breeds